Home > Error Code > Case Ih Puma Error Codes

Case Ih Puma Error Codes

Contents

What can I do? Possible service brake bottom brake switches open. Control - SOURCE LOW NH 3109 CC HS Power stage 1 fuel press. Give the new profile a distinctive name. 4. this contact form

It is recommended to back up the data and clear the display before the internal disk space used reaches 50%, to increase system performance. ENG 2973 Intake Manifold 1 Pressure data invalid. I have an offset header installed on my combine. Hitch 1006 EDC Low Side Driver stuck on failure.

List Of New Holland Error Codes

Do not use a removable memory device larger than 4GB in the display. Does the Pro 700 save data to the internal memory of the display? Engine 3019 Boost Pressure Sensor -Signal Above Range Max.

ENG 131 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too high ENG 132 Decelerator or Hand Throttle (STD cab) Position potentiometer voltage is too low ENG 133 Decelerator Attach the .zip file to an email message. Select all 6 loads and calibrate. Case Excavator Fault Codes Generated Fri, 18 Nov 2016 17:26:48 GMT by s_sg2 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection

Once in the menu, select "Info" Info will display the following: swath name recorded date type DGPS correction Heading A point coordinates B point coordinates Note: this feature is available in Case Backhoe Fault Codes If the display is reading dashes, you are missing one of the following: Weight, Wet Crop Moisture Crop Trade Moisture ( Set in Calibrations > Crop) Working Width (Greater than 0) To calculate the total NH3 from the actual nitrogen, multiply the actual nitrogen value by 1.22. When selecting the Units of Measure to be used in the AFS Pro 600 and AFS Pro 700 (Toolbox > Operator Setup), what is the difference between "Imperial" and "USA"?

Email Address: OR Log-in User Name Password Remember Me? New Holland Error Code 14101 NH 4043 Controller Fault ( Register check) NH 4044 Controller Fault (Flash Memory) NH 4045 Controller Fault (Data Memory) NH 4100 Remote No.1 No control Message Received NH 4101 Remote No.1 Please try the request again. To reset calibration values to default, import Default values for the selected Crop Type on the Calibrations > Crop screen.

Case Backhoe Fault Codes

Checked parameters will be monitored by the telematics unit and reported to the portal. ENG 1117 Battery voltage too low, or the controller was not allowed to power down correctly ENG 1256 Control Module Identification Input State Error. List Of New Holland Error Codes However, Case IH recommends a travel distance of 400'. Scr Failure Case Ih How many swaths can the AFS Pro 600 or AFS Pro 700 store at one time?

Ensure that the grain tank is empty before beginning harvest. weblink This can be located roughtly six inches from the display connector. Unchecked ones will not. Related product:AFS Pro 600AFS Pro 700Combine Yield Monitoring Yes.  Just remember that you will need to complete loads (Tasks) at different flow rates and in some Crop Types is will take Case Ih Combine Error Codes

If the center of the header is to the RIGHT of the GPS receiver, the Header Center Offset will be a positive value. Posting Quick Reply - Please WaitPosting Quick Reply - Please Wait « Previous Thread | Next Thread » Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) ENG 551 Hand Throttle (STD cab) Idle Validation Switches are both open ENG 553 Front fueling actuator overfueling ENG 559 Front fueling actuator underfueling ENG 581 Fuel inlet Pressure Sensor voltage http://winnport.com/error-code/case-error-code-14101.html ENG 418 Water in Fuel sensor indicates the water in the fuel filter needs to be drained.

What is the FM-1000+ application used for on the XCN-2050 display? Ford New Holland Fault Codes Which one should I use? Use cable 87298129, or, if the cable is completely inside the cab, use 380002422.

Where can I check this?

ENG 153 Intake Manifold Temperature Sensor voltage is too high ENG 154 Intake Manifold Temperature Sensor voltage is too low ENG 155 Intake Manifold Temperature level has exceeded the warning limit. If "Hitch Implement" is selected, the implement is considered to be "working" when the hitch is lowered, and "not working" when the hitch is raised, based on the Implement Working Depth This will ensure that performance is not negatively affected by machine maintenance (new elevator chain or paddles, different flow sensor impact plate, etc.) or by crop characteristics (density, texture, etc.). Case Skid Steer Error Codes ENG 2266 Electric Lift Pump for Engine Fuel Supply Voltage too low.

The Default Rate assigned in the Product Setup screen (Toolbox > Product) is only used during manual product application. ENG 758 Rear Bank injector is bad ENG 951 A power imbalance between the cylinders was detected by the controller hardware ENG 983 Unused A/D input channel out of range. Engine 3028 Oil Pressure Too Low Engine 3029 Oil Pressure Sensor _Short circuit to Battery Engine 3030 Oil Pressure Sensor _Short circuit to Ground Engine 3031 Oil Pressure Sensor -Hardware Error his comment is here This is the only supported flash drive for use in the AFS Pro 700.

Today 07:48 AM by David Vines 9 Liquid ballast in rear... Names should be kept to 8 characters or less to display properly on the run screens. Related product:AFS Connect 2.0 Yes, AFS connect can still be used. TRANS 74 The park brake ON with gear is engaged - no park brake request from calibration.

Related product:AFS Pro 300AFS Pro 600AFS Pro 700Combine Yield Monitoring If your moisture in the display is reading the same as the manual moisture setting in calibrations crop, it is because Notice: How to donate and get more Galons 22.01.2015 ? Related product:AFS Pro 300AFS Pro 600AFS Pro 700 To check the software versions installed on your AFS display, go to Home > Diagnostics > Version. Create a new layout (recommend using operator's name).

ENG 758 Rear Bank injector is bad ENG 951 A power imbalance between the cylinders was detected by the controller hardware ENG 983 Unused A/D input channel out of range. Trans 2074 FNR Not Park Switch low voltage fault Trans 2075 FNR Not Park Switch high Voltage fault Trans 2110 FNR Neutral Switch Low Voltage fault Trans 2111 FNR Neutral Switch NH 4191 No communications from ( EHR) No.2. NH 14901 Engine controller not present (EDC7) NH 14902 Auxiliry (optional) Controller Module missing (DD/DH).