Home > Error Code > Canon Super G3 Error Codes

Canon Super G3 Error Codes

Contents

Cause: Abnormal protocol. Cause: Increase #2 MENU No. 07 transmission level within a range of -8 to -15 dBm, or set #1 SSSW SW28 bit 0 to 1 to inhibit the V.8/ V.34 protocol A. Cause: Cannot receive picture signals properly due to poor line conditions. Check This Out

Cause: Cannot receive picture signals properly from the other party due to poor line conditions. Sign up now Login × Sign Up for ManualsOnline    Login with Facebook Agree to Terms and Privacy Policy Sign Up ERROR The requested URL could not be retrieved The following error Cause: Carriage installation surface is defective. Cause: Cannot receive signals properly due to poor line conditions.

Canon Fax Error Code Ng

Solution: Boost the transmission level so signals can be properly received by the other party. Page 123 Chapter 2: Service Error Codes ##327 [ RX ] Printer (LBP) is faulty Cause Remedy • An internal unit is faulty (i.e., the vertical • Correct it by referring Image Signal: Of procedure signals, it is used for actual transmission of image data. A.

Page 100 Chapter 2: Service Error Codes ##263 [ TX/RX ] After detection of a preamble, no response is received for 20 sec Cause Remedy • The line has noise of D. Cause: Defective internal unit; (the wait signal will not go off for 3 seconds when waiting to respond to the reader after pre-scanning the document length). Canon Error #099 Match the closed network ID: Match the settings of SW08 bit through bit 7.

Solution: Power cycle the machine. Canon Fax Machine Error Codes Solution: Replace the board containing the Thermistor ##347 [ TX / RX ] BJ printer control ROM/ RAM check error. A. Solution: Replace the read end sensor. 2.

A. Fax Error Codes Ricoh Page 36 Chapter1: User Error Codes #044 [ RX ] The size of the recording paper and that of the ink sheet cartridge do not mach Cause Remedy • The size Solution: Have the other party boost their transmission level to receive REJ properly. ##715 [ TX ] Receive signals other than RR, RNR or REJ after retransmission procedures during ARQ A.

Canon Fax Machine Error Codes

Cause: SCNT PWB malfunction. Cause: Cannot receive the picture signals from the other party properly due to poor line conditions. Canon Fax Error Code Ng Cause: BJ printer control ROM error Solution: Power cycle the machine (unplug unit). Canon Fax Error #018 Remedy Re-enter the destination in the Address Book, and try sending again.

This can be due to an power outage or not enough electricity flowing into the machine. his comment is here A. A. Solution: Replace cutter. Fax G3

Enjoy everyday low prices and get everything you need for a home office or …… Error Code Table (listed by number) … Canon's ultra-high quality image processing produces excellent reproductions in Solution: Retransmit. Cause: Defective internal unit; (CS will not set 0 when RS is set to 0). this contact form B.

other party can receive NACK correctly. Canon Super G3 Troubleshooting Page 189 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. A.

Solution: Add an EPT on the V29 modem signals.

Remedy Allow Fax Driver TX in Send in Function Settings (Settings/Registration) is set to 'Off'. xglys Desktop ready laser fax delivering quick results whether faxing, printing, or copying What Other Items Do Customers Buy After Viewing This Item? Solution: Adjust the NL equalizer so the other party can receive TCF properly Solution: Take echo counter-measures as described in Service manual. Toshiba Fax Error Codes Page 108 [ TX ] After transmitting EOP, a signal other than PIN, PIP, MCF, RTP, or RTN was received Cause Remedy • The procedure signal has a fault. • Record

Solution: Boost the transmission level so the other party can receive MCF2 or PIS. Page 62 Chapter 2: Service Error Codes ##003 [ TX ] In G2 transmission, MCF2 or PIS cannot be received Cause Remedy • The line condition is poor, and the other Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##113 [ TX ] Receive signals other than MFC, RTP, RTN, PIP navigate here Cause: Defective internal unit; (byte pack interrupt was not generated).

Page 145 Chapter 2: Service Error Codes ##606 [ RX ] In MF1 (Minifax 1) reception, phase synchronization fails [Japanese mode] Cause Remedy • The line condition is poor, and the Page 83 Chapter 2: Service Error Codes ##122 [ TX ] ITU-T-compliant (DIS bits 33 through 37) transmission function is absent Cause Remedy • Bit 33 of DIS received from the Cause: Picture signal or RR was not properly transmitted due to poor line conditions. T.62 T2 Timer: It is the period of time in which the machine waits for a response as part of a channel B communication procedure.

Solution: Install another BJ cartridge. Solution: Adjust the NL equalizer so the other party can receive picture or Q signals properly. Cause: Abnormal protocol. Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the

A. Cause: Stop button was pressed during communication Solution: Retransmit ##286 [ TX ] DCN reception after EOM transmission. error). • Replace the PCB that includes the modem. ##271 [ RX ] After transmitting CFR, 1650 Hz (frequency component of a binary signal) was... B.

A. Page 67 Chapter 2: Service Error Codes ##013 [ TX ] In G2 transmission, PIS is received while transmitting an image signal Cause Remedy • The other party has run out Solution: Have the other party relax their RTN transmission conditions so they will not transmit RTN. Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the

Cause: The BJ controller in the BJ printer control unit is faulty. Page 161 • The procedure signal (the nature of REJ • Record the protocol on a DAT or MD, and from the other party) is faulty. and/or Technical Center. 1. Solution: Refer to Service Manual. ##306 [ TX ] System error between modem and MCPU.