Home > Canon Printer > Canon Printer Ip6600d Error Code 6a00

Canon Printer Ip6600d Error Code 6a00

Contents

Check towels and replace. i need to get a tack that was lodged in the middle of the printer.thanks!Nolan by nolany on Nov 9, 2007 at 2:56pm Add comment Please sign in to comment 0 Followed suggestion by inkjetonline above. Red requires almost 100\% of yellow and magenta. Check This Out

The service center wants me to drive the thing 85 miles one way for somebody to look at it. When we see it in the shop, 9 out of 10 times its a jammed purge unit. Don't touch the electrical points at the back with your fingers. i then turned the printer aff then on and it works well now. - Anonymous OMG thank you so much!

Canon Printer Error Code 6a00

ztarrfect 197,924 views 17:12 Canon MG5250 and error B200 - Duration: 1:49. I moved the print heads back and forth a couple of times to make sure there was no more paper stuck, turned it off and on and yes ahhhh it works Hope this help by Anonymous on Mar 9, 2007 at 11:32pm Add comment Please sign in to comment This did the trick. Since it's out of warranty, I figure any significant repair would cost more than printer is worth.

I have just posted my experience on another thread, but I thought it was worth copying here ...I had the dreaded ambiguous 6A00 on my 2 Sign Up Login Add Question It works, thank you!!! by unknown on Oct 29, 2006 at 5:53pm Add comment Please sign in to comment Many thanks to all of you who posted about this. Canon Mp530 Check Printer 6a00 I turned the printer back on and it works great!!BTW, Cannon did want me to send it for sevice too!!!

by unknown on Sep 30, 2007 at 8:46pm Add comment Please sign in to comment 0 I have a canon MP500 and I've been getting the 6A00 code. by unknown on Apr 27, 2009 at 8:42pm Add comment Please sign in to comment 1 I moved the print carraige all the way to the left (power off)found and removed You will break something if is is jammed and you need a much closer inspection to try and remove the jam. Will keep a note about this website as you guys are all fantastic.

Doing printhead cleans wastes ink but its an important part.Do a test print of a small amount of text in different colours. Canon A6000 Be persistent as it took a number of cleanings before getting it too work. The Canon website was not helpful at all. when i moved the printer ink and turned the printer off and the the flashlite on I noticed some small chardes of paper in a far corner and after I removed

Canon Printer Error 6a00 Mp610

I've tried many of the suggestions recommended on this forum, including cleaning the print head and other areas that I can reach and/or remove, and making sure the purge cleaning station It also has a an electrical pump to milk the print heads and test for ink flow. Canon Printer Error Code 6a00 by unknown on Jul 13, 2007 at 8:47pm Add comment Please sign in to comment 0 I have a i4000 purchased in November 04. Canon Mp600 Error Code 6a00 Could the problem be something to do with this?Thanks in advance for any help you can give!

Add it up! - unknown worked!!!THANK YOU VERY MUCH - Anonymous Yeah! his comment is here You appear very knowledgable about this so any help would be great. There was a paper clip sitting in there with ink all over it. The green light (green only) blinks, as if it were waiting for data.I tried uninstalling the printer driver (under xp) v1.80 and reinstalling. Canon 6a00

Reply Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous However, mine was still getting stuck after I cleaned it. so I can look more closely... http://winnport.com/canon-printer/canon-pixma-ip6600d-error-6a00.html The “L” shaped piece was moved forward out of its place.

Take care! - Anonymous 0 Had the printer a week and a half. Sony A600 Trial and error will release the right ones first. I am now covered with ink and have a one month old o contend with.Anything I can try before my head pops off or I have to go buy a new

I would suggest doing this at least every six months.

DiKu4CIAOde 34,535 views 2:20 Canon Pixma Mp830 Review Full - Duration: 13:46. Thanks very much!My printer now works :)Thanks againH - unknown 0 All the above sounds great, except that my ink carriage wouldn't move to the left. and turned it on while holding down reset (that's old-school). Canon Printers Removing a paper jam could have caused it in the first place, especially if the paper tore and you had bits every where.

Expand Popular Products Canon PIXMA MP160 All-In-One InkJet Printer 2,377 Questions Canon PIXMA MP150 All-In-One InkJet Printer 2,263 Questions Canon PIXMA MX310 All-In-One Printer 2,008 Questions Canon PIXMA MP830 All-In-One InkJet I see a lot of people bashing Canon, but as long as it's under warranty, they replace it quickly. It will move slightly up and down but not laterally. navigate here It wasn't moving; so, I moved it myself.

When will these idiots realize that people will find a way around everything. Please advise Submitted: 5 years ago. It is not all the way to the right but approximately 1 1/2 from the complete right of the carriage resting area.Once blotting was complete:-Carriage returned to resting position to the by unknown on Apr 16, 2007 at 9:00am Add comment Please sign in to comment Hello,Yes I Can Confirm Moving The Cartridge Carridge Back to the left and reaching in and

thank you thank you thank you.... Removed Print head cartridge and wiped out excess ink stuck on bottom.10. This is where the print-head is homed/parked and is the top of the WIA unit.3. It also has a an electrical pump to milk the print heads and test for ink flow.

It isn't going to hurt anything if it overflows a little. I am an authorized Canon tech for Faxphone, pixmas, printers, copiers including image class, multipass units. When it is parked there, pull the power cord out of the printer. I am confused about what exactly is a purge unit (does mine have one, and how do I identify it, access it, clean and/or move it?).The print head holder on my

Usually, 8-10 layers of "Scot Single Ply" will work best. The error is gone, it all works fine again.