Canon Pixma Error Code 5000
The main controller PCB is faulty.Mode of Detection:0000 An error has occurred in communication between the CPU of the control panel CPU PCB and the main controller PCB.E248Main Cause: The EEPROM The DC controller PCB is faulty.Mode ofDetection0000 While the hard disk fan (FM7) is being driven, the clock signal(FM7CLK) does not arrive for 5 secs or more. why? I'm on vacation right now and don't have my files with me. http://winnport.com/canon-pixma/canon-pixma-ip6220d-error-code.html
E540Main Cause The tray home position sensor (PI8) is faulty. The main controller PCB is faulty.Mode ofDetection0000 An error has occurred in the PCI bus.E742Main Cause The RIP1 board (accessory) is faulty. E5F1Main Cause The folding motor clock sensor (PI4S) is faulty. The hopper motor (M9/M10) is faulty.The toner sensor (TS1/TS2) is faulty.
When an error occurs, check the support code displayed on the LCD or the computer screen and take the appropriate action. The paperpositioning plate motor (M4S) is faulty. by unknown on Jan 13, 2012 at 9:20am Add comment Please sign in to comment 0 The wiper blades are clean and retracted, i moved them to test if it slide
E590Main Cause The punch home position sensor (PI3P) is faulty. The puncherdriver PCB is faulty.Mode ofDetection0001 When the power switch is turned on, the check sum of theEEPROM on the finisher controller PCB is found to have an error.0002 When the I will send you the test process for the 5C00 error condition. The hard disk drive isfaulty.
The DC controller PCB is faulty.Mode ofDetection0000 While the primary charging assembly cooling fan is being driven, E412Main Cause The cooling fan (FM1) is faulty. Your Own Question Freddy M., Technician Category: Printers Satisfied Customers: 18398 Experience: Years of IT and customer support experience 15852642 Type Your Printers Question Here... The front door switch (MS2S) isfaulty. I have borrowed sons printer as mine was playing up and the error code keeps coming up.Please help me!!!!Thank you Respond to this 0 Found this on http://slayo.com/Resetting Printer Canon MP140,
Did this answer your question? E804Main Cause The wiring is faulty (short circuit, open circuit). Have a manual for Canon Pixma MP500 All-In-One InkJet Printer? Sometimes the purge unit stops in the middle, sometimes in the forward position, sometime in the backward position with the pads down.
by unknown on Jun 4, 2010 at 3:47pm Add comment Please sign in to comment 0 Mikele707,.... Once the power is off you can now move the carriage to the far left so it is out of the way. The saddle stitcher controller PCB is faulty.Mode ofDetection0001 The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0.3 sec ormore.0002 I know the instructions above are wrong and you have probably figured that out by now.
Then I got an error message "5000". http://winnport.com/canon-pixma/canon-pixma-mp150-error-e5-code.html Load paper back into the ASF or cassette.9. There is a lot of info on the web how to do this, but nothing really seems to be true.Actually Canon does not either really approach this in a friendly way. E420Main Cause The EEPROM is faulty.
The DC controller PCB is faulty.Mode of Detection0001 Although the controller cooling fan (FM4) is being driven, the clock signal (FM4LCK) does not arrive for 5 secs or more.E196Main Cause: The The paperpush-on plate leading edge position sensor (PI15S) is faulty. I would expect Canon refill packages and guidelines on how to make sure that your printer is in optimal status. Check This Out The tray upper limit detecting switch (MS5)is faulty.
Before I provide you any instructions on how to use the Service Mode, you need to post some information explaining what you printer problem is, and what you have done to the printer is used. The DC controller PCB is faulty.Mode ofDetection0000 While the DC power supply fan is being driven, the clock signal(FM6CLK) does not arrive for 5 secs or more.
The finisher controller PCB isfaulty.Mode ofDetection0002 The communication between the saddle stitcher controller PCBand the finisher controller PCB has been interrupted.E504Main Cause The height sensor (PS1) is faulty.
The punch motor (M1P)is faulty. The paper push-onplate motor (M8S) is faulty. Question about Canon PIXMA Printers & Copiers 1 Answer Pixma ip500 error message 5C00 - what does it mean? ...5000 and have started getting an error message 5C00 asking me to Once that power is off you can now move the carriage to the far left so it is out of the way.
and 4 other Printers Specialists are ready to help you Ask your own question now Share this conversation Related Printers Questions Question Date Submitted My printer is no longer working after Thesaddle stitcher controller PCB is faulty.Mode ofDetection0001 The number of detection pulses of the folding motor clock sensordrops below a specific value.0002 The state of the paper folding home position sensor Once you get that send me back a note with your current status. http://winnport.com/canon-pixma/canon-pixma-mp780-error-code-336.html Thanks - Anonymous need help with my mp830 send me instructions to clear error code 5C00 Thanks - Anonymous 0 I am not sure I understand this forum - I posted